国产午夜一区二区在线观看m_免费a级毛片高清_亚洲欧美高清播放器在线_国产在线午夜视频_aⅤ免费久久精品_亚洲A级毛片不卡_免费电影 AV 中文_韩国午夜理伦三级网_国产自怕一区二区三区_婷深夜综合成人aⅴ网站

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo cylinder Sold to Kazakhstan

Release time:2023-11-15 10:42:18 Hits: Current position: Home > News

This article mainly introduces:

Kazakhstan hydraulic cylinder,servo cylinder manufacturer,servo cylinder

Kazakhstan servo cylinder

(Kazakhstan servo cylinder,produced by Hengyu Group)

servo cylinder are widely used in Kazakhstan,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed servo cylinder for customers from Kazakhstan.

Introduction to servo cylinder:

The difference between the integral servo cylinder and the split servo cylinder: The integral servo cylinder and the split servo cylinder in the servo cylinder are two different servo cylinders, and they are very different. The whole servo cylinder, which is cast in one body, is not prone to problems such as oil leakage; The split servo cylinder is welded twice, so if it is not handled well at the welding, it is prone to problems such as oil leakage and servo cylinder damage. Therefore, it is obvious that the answer to this question is for difference.

The servo cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure servo cylinder can use 20 steel pipe, and the high pressure servo cylinder can use 45 steel pipe.

The difference between the integral servo cylinder and the split servo cylinder: The integral servo cylinder and the split servo cylinder in the servo cylinder are two different servo cylinders, and they are very different. The whole servo cylinder, which is cast in one body, is not prone to problems such as oil leakage; The split servo cylinder is welded twice, so if it is not handled well at the welding, it is prone to problems such as oil leakage and servo cylinder damage. Therefore, it is obvious that the answer to this question is for difference.

The servo cylinder is not the same as the servo cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the servo cylinder can not be used as a high-power power component, but the servo cylinder can be used as a relatively large power component, or the servo cylinder system can be used.

Answers to some questions about servo cylinder:

Can the hydraulic oil in the cylinder return to the tank?
Yes, there is a way, for example, first remove the cylinder from the machine, and then connect the two pipes on the cylinder, so that the cylinder piston rod is completely retracted into the cylinder, at this time, the piston is with the bottom, and the rear chamber is almost no oil, and then screw off the joint at the end of the front chamber by the hydraulic station, and put it in an empty bucket. Finally, insert the gas pipe into the oil port of the rear chamber. Open the air source, and then the rod will run out, and you'll drain the hydraulic oil from the end of the rod, which requires a source of air on site.

When the hydraulic cylinder changes from fast to slow, how can the slow speed become more even and the speed can be adjusted?
Reversing valve set 2 reversing valves. The back of one valve goes directly to the cylinder, running at full speed for fast action. Add a speed control valve behind the other valve, and then connect to the cylinder to achieve slow action, you can adjust the opening of the speed control valve, to achieve the speed of the cylinder can be adjusted. An import speed control valve to more than 1,000 yuan, if you think it is too expensive, you can also use the throttle valve instead. However, the throttle valve is greatly affected by the load change.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP