This article mainly introduces:

Uganda hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

(Uganda tilting furnace hydraulic cylinder,produced by Hengyu Group）

tilting furnace hydraulic cylinder are widely used in Uganda，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed tilting furnace hydraulic cylinder for customers from Uganda.

Introduction to tilting furnace hydraulic cylinder:

In the process of using the tilting furnace hydraulic cylinder, sometimes such a problem will occur, the tilting furnace hydraulic cylinder can not act immediately after the instruction of the tilting furnace hydraulic cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil tilting furnace hydraulic cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

tilting furnace hydraulic cylinder buffer valve inspection and maintenance: For the valve buffer tilting furnace hydraulic cylinder, the focus should be on checking the wear of the buffer valve spool and seat. Once it is found that the amount of wear increases and the seal fails, it should be replaced. It can also be repaired by using abrasive spool and seat matching grinding method.

If the tilting furnace hydraulic cylinder slips or crawls, please check whether there is astringency inside the tilting furnace hydraulic cylinder, because the internal parts of the tilting furnace hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the tilting furnace hydraulic cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the tilting furnace hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

Improve the service life of the tilting furnace hydraulic cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the tilting furnace hydraulic cylinder (such as the tilting furnace hydraulic cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the tilting furnace hydraulic cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the tilting furnace hydraulic cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single tilting furnace hydraulic cylinder exhaust.

Answers to some questions about tilting furnace hydraulic cylinder:

How to calculate the tonnage of hydraulic cylinder? The tonnage of the cylinder refers to the output force of the cylinder under rated working pressure: 1, for single rod piston hydraulic cylinder, it can be calculated by the area of the circle corresponding to the inner diameter of the cylinder A (square centimeter), and the rated working pressure of the system p (mpa), the value is equal to 10pA kg force, and the ton is 0.01pA. 2, for the double rod piston hydraulic cylinder, with A(square centimeter) to indicate the cylinder cylinder diameter and piston rod outer diameter defined by the ring area, with p (mpa) to indicate the rated working pressure of the system, the output force of the cylinder is 0.01pA ton force.

What is the rated pressure of the general cylinder?
This depends on the model of the cylinder, 1. The rated pressure of the light tie rod cylinder is 7 series 7MPa and 14 series 14MPa. 2. Rated pressure of engineering cylinder 16MPa. 3. Rexroth type metallurgical cylinder rated pressure 250MPa.