国产午夜一区二区在线观看m_免费a级毛片高清_亚洲欧美高清播放器在线_国产在线午夜视频_aⅤ免费久久精品_亚洲A级毛片不卡_免费电影 AV 中文_韩国午夜理伦三级网_国产自怕一区二区三区_婷深夜综合成人aⅴ网站

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

pusher hydraulic cylinder Sold to Turkey

Release time:2023-12-02 14:47:40 Hits: Current position: Home > News

This article mainly introduces:

Turkey hydraulic cylinder,pusher hydraulic cylinder manufacturer,pusher hydraulic cylinder

Turkey pusher hydraulic cylinder

(Turkey pusher hydraulic cylinder,produced by Hengyu Group)

pusher hydraulic cylinder are widely used in Turkey,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed pusher hydraulic cylinder for customers from Turkey.

Introduction to pusher hydraulic cylinder:

The pressure of the sliding surface of the pusher hydraulic cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the pusher hydraulic cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

Disassembly pusher hydraulic cylinder: When disassembly pusher hydraulic cylinder, strictly prevent damage to the screw thread at the top of the piston rod, the screw thread of the pusher hydraulic cylinder head and the surface of the piston rod. It should also be noted that the piston cannot be played out from the pusher hydraulic cylinder.

In use, the pusher hydraulic cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the pusher hydraulic cylinder.

When the pusher hydraulic cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the pusher hydraulic cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

Answers to some questions about pusher hydraulic cylinder:

Hydraulic system schematic diagram, pipeline identification S and L, respectively corresponding nominal diameters? 16S is equivalent to DN12 high-pressure cylinder, and 15L means what?
16S refers to the high pressure series, outer diameter 16x2 steel pipe, the corresponding sleeve nut is M24X1.515L is the low pressure series, the outer diameter of 15x1.5 steel pipe, the corresponding sleeve nut is M22X1.5.

Why the lifting cylinder falling by itself?
May be there is a pressure relief point. Check and repair the following parts: whether there is oil leakage in the transparent pipe at the top of the cylinder: the cylinder oil seal is broken, and the cylinder and oil seal need to be replaced; No: The multiway valve has pressure relief and needs to be repaired. Maintenance in accordance with routine maintenance items can reduce mechanical failures: 1. Check whether the thermostat works normally. 2, check the transmission shift work is normal. 3. Check the tightness of the fan belt. 4, check whether the diesel tank oil inlet filter is blocked or damaged, and clean or replace the filter. 5. Check and adjust the valve clearance.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP