国产午夜一区二区在线观看m_免费a级毛片高清_亚洲欧美高清播放器在线_国产在线午夜视频_aⅤ免费久久精品_亚洲A级毛片不卡_免费电影 AV 中文_韩国午夜理伦三级网_国产自怕一区二区三区_婷深夜综合成人aⅴ网站

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tailplate hydraulic cylinder Sold to Chile

Release time:2023-11-28 10:55:25 Hits: Current position: Home > News

This article mainly introduces:

Chile hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

Chile tailplate hydraulic cylinder

(Chile tailplate hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

tailplate hydraulic cylinder are widely used in Chile,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed tailplate hydraulic cylinder for customers from Chile.

Introduction to tailplate hydraulic cylinder:

When the long-stroke tailplate hydraulic cylinder rotates horizontally, the piston rod bends due to its own weight, causing the guide sleeve and piston to produce biased load, resulting in tailplate hydraulic cylinder head seal damage, oil leakage, and piston sleep in the tailplate hydraulic cylinder. The following measures can be taken: increase the piston plan to adjust the piston outer circle and process it into a convex drum, so that the piston can self-position, improve the force situation, and reduce and avoid pulling the tailplate hydraulic cylinder; The piston and the piston rod are connected with a spherical joint.

Before the tailplate hydraulic cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

tailplate hydraulic cylinder head explanation: low pressure castings, medium and low pressure with HT300 gray iron, medium and high pressure with 35, 45 steel. When the tailplate hydraulic cylinder head itself is the guide sleeve of the piston rod, the tailplate hydraulic cylinder head is best cast iron. At the same time, brass, bronze or other wear-resistant materials should be fused on the guide surface. If the guide sleeve is pressed into the tailplate hydraulic cylinder head, the guide sleeve shall be wear-resistant cast iron, bronze or brass.

When the tailplate hydraulic cylinder is disassembled due to oil leakage and other faults, the position of the piston should be moved to any end position of the tailplate hydraulic cylinder by applying liquid pressure. Improper tapping and sudden drop should be avoided during disassembly.

Answers to some questions about tailplate hydraulic cylinder:

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.

What are the connection methods of the hydraulic cylinder? The connection modes of the cylinder and the actuator are earring connection, hinge shaft connection, thread connection, etc. The connection modes of tubing and cylinder are threaded connection, flange connection, etc.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP