国产午夜一区二区在线观看m_免费a级毛片高清_亚洲欧美高清播放器在线_国产在线午夜视频_aⅤ免费久久精品_亚洲A级毛片不卡_免费电影 AV 中文_韩国午夜理伦三级网_国产自怕一区二区三区_婷深夜综合成人aⅴ网站

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

hydraulic forklift cylinder Sold to Panama

Release time:2023-11-08 08:11:33 Hits: Current position: Home > News

This article mainly introduces:

Panama hydraulic cylinder,hydraulic forklift cylinder manufacturer,hydraulic forklift cylinder

Panama hydraulic forklift cylinder

(Panama hydraulic forklift cylinder,produced by Hengyu Hydraulic Cylinder Factory)

hydraulic forklift cylinder are widely used in Panama,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed hydraulic forklift cylinder for customers from Panama.

Introduction to hydraulic forklift cylinder:

Factors that should be considered when selecting the oil seal in the hydraulic forklift cylinder: some specific factors should be taken into account when selecting the oil seal in the hydraulic forklift cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: hydraulic forklift cylinder diameter, piston rod diameter, piston rod and piston groove size, hydraulic forklift cylinder working pressure, hydraulic forklift cylinder movement speed, hydraulic system oil temperature and hydraulic forklift cylinder working environment.

The commonly used buffer structure of the hydraulic forklift cylinder is composed of a piston boss and a hydraulic forklift cylinder head groove. When the piston moves close to the hydraulic forklift cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

The hydraulic forklift cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the hydraulic forklift cylinder, bite. Elimination method: When installing the hydraulic forklift cylinder, ensure that the axis position of the hydraulic forklift cylinder is consistent with the direction of movement; Make the load borne by the hydraulic forklift cylinder as far as possible through the hydraulic forklift cylinder axis, to avoid the phenomenon of eccentricity.

After the hydraulic forklift cylinder is installed, lubricating grease should be added to the relative moving parts such as earring and middle hinge shaft before trial operation.

Answers to some questions about hydraulic forklift cylinder:

What valve is used to control the speed of the cylinder?
Hydraulic cylinder for lifting is generally the piston rod downward installation, to achieve the fast and slow speed of the cylinder, you can add a two-digit three-way electromagnetic reversing valve + a throttle valve on a branch at the bottom of the cylinder, you can achieve speed change, control mode can be controlled by time control can also be controlled by stroke switch. If you want to achieve more accurate control can use proportional valve control.

Hydraulic system schematic diagram, pipeline identification S and L, respectively corresponding nominal diameters? 16S is equivalent to DN12 high-pressure cylinder, and 15L means what?
16S refers to the high pressure series, outer diameter 16x2 steel pipe, the corresponding sleeve nut is M24X1.515L is the low pressure series, the outer diameter of 15x1.5 steel pipe, the corresponding sleeve nut is M22X1.5.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP